在为您的工作选择合适的填料后，可使用它来增胶树脂混合物所需的稠度。特定工作所需的混合物的厚度由添加的填料量控制。混合一批增胶树脂的步骤如下：

After selecting the right filler for your job, you can use it to increase the resin mixture to the desired consistency. The thickness of the mixture required for a particular job is controlled by the amount of filler added. The steps for mixing a batch of sizing resin are as follows:

在添加填料之前，将环氧树脂胶和固化剂混合在一起。使用桨刮擦角落和侧面。

Before adding filler, mix epoxy resin adhesive and curing agent together. Scrape corners and sides with paddles.

将测量的填料量添加到桶中。

Add the measured amount of filler to the bucket.

用早先准备的开槽盖盖住桶。

Cover the bucket with the slotted cover prepared earlier.

将搅拌器通过盖子插入环氧树脂中。

Insert the stirrer through the cover into the epoxy resin.

慢慢启动搅拌机，逐渐增加速度。

Start the mixer slowly and gradually increase the speed.

上下左右移动混合器，将填料与环氧树脂混合。当填料开始混合时，厚批量的环氧树脂将使电机运转。随着混合物变得光滑和乳脂状，这将变得容易。

Move the mixer up, down, left and right to mix the filler with epoxy resin. When the filler begins to mix, a thick batch of epoxy resin will first run the motor. This will become easier as the mixture becomes smooth and creamy.

从桶上取下盖子和搅拌器。

Remove the lid and stirrer from the bucket.

刮掉桶的角落，将剩余的未增胶树脂与剩余的批次混合。

Scrape off the corners of the barrel and mix the remaining unsized resin with the remaining batch.

将搅拌器放回原处并短暂搅拌直混合均匀。

Put the stirrer back and stir briefly until the mixture is uniform.

氢氧化钾厂家提醒您记住将完成的混合物摊开或快速涂抹，以免过热。

The potassium hydroxide manufacturer reminds you to spread out or quickly smear the finished mixture to avoid overheating.

在混合大批量之前，请考虑质量控制。树脂和固化剂须充分混合，我们都知道这一点，但在大型项目中时间紧迫时往往会忘记这一点。这不是寻找捷径的地方，如果您不遵循某些准则，那么再精良的电动搅拌机也将无法弥补。

Before mixing large quantities, please consider quality control. We all know that the resin and curing agent must be fully mixed, but we often forget this when time is tight in large projects. This is not a place to find a shortcut. If you don't follow certain rules, no matter how sophisticated the electric mixer is, it will not be able to make up for it.

为获得大强度，仅添加足够的填料以完全弥合表面之间的间隙，而不会下垂或超出接缝或间隙。对于较稠的混合物，在添加填料之前，不要将混合杯填充超过1/3的环氧树脂胶。

In order to obtain high strength, only enough filler shall be added to completely fill the gap between the surfaces without sagging or exceeding the joints or gaps. For thicker mixtures, do not fill the mixing cup with more than 1 / 3 epoxy resin glue before adding filler.

更多关于这一方面化工产品的信息获取，您可以来我们网站http://www.jinhao360.com咨询了解。

For more information about chemical products in this area, you can visit our website http://www.jinhao360.com Consultation and understanding.